- 泽任订制
- FST动物实验器械
- 瑞士ideal-tek镊子
- 瑞士Dumont镊子
- Weller
- Techni-Tool
- 瑞士Rubis镊子
- arosurgica
- Genesee Scientific
- Gilder Grids
-
Entegris
- WEICON
- ACCURIS
- AIMS
- RMC钻石刀
- Sipel镊子
- 德国WIHA
-
Si-Mat
- Jokari
- Circuitmedic
-
Glissando病理切片扫描仪
- KNIPEX(凯尼派克)
- Swann-morton
- Cellpoint Scientific
- Swanstrom
- All-spec
- 新华器械
- Excelta
- MENDA
- MEISEI
- Erem
- Regine
-
OPTRASCAN病理扫描仪
- Benchmark
-
IDEAL
- 大龙仪器
- 五洋医疗
- Hozan(宝山)
- 3M
- Stoelting
- Roboz
-
Diatome钻石刀
- Fine Science Tools
- PLATO
- NanoSoft
-
Avantama
-
PSI打击器及配件
- Aptum
- xuron
- SPI
-
抗原检测
- ASI Instruments
-
上海一恒
-
上海雷磁
- Quantifoil
- 上海方需
- 苏州六六
-
Hamilton
- ISMART
-
显微镜
-
Bonllmann
- AVEN
- 塔望科技
-
瑞典Haglof激光测距仪
- STILLE
-
美国安维迪
- 德国贝朗蛇牌
- Medline
-
蛋白纯化系统
-
OHAUS奥豪斯
- 康博特森
- Ossila
- 赛宁(苏州)生物
- Bernstein
- 洁盟清洗机
- Ted Pella
- DSI
- Keller
-
Smart Tweezers
- 瑞士PB
-
Microscopes Internat...
- Lattice Gear
-
凯氏定氮仪
- lindstrom
- 美国EMS
-
1-material
-
仪器
- realisticflies
- Boive
- Zivic
Epo-Fix embedding kit, small (DG)
Epo-Fix is an original product that was formerly only available in the metallographic field. We discovered that it is a perfect embedding media for the majority of material specimens after thorough testing in our laboratory.
LR White was by far the most widely used embedding media for materials due to its block hardness, although it has drawbacks.
For example, the specimen's adhesion is low, and additives are necessary to increase the specimen's adhesion. Another big issue is the difficulty to appropriately orient the specimen in order to cut your block later.This is simply due to the fact that LR White requires oxygen deprivation, therefore the manufacturer recommends using gelatine capsules (vertical). Another issue is that polymerisation might take up to 24 hours in the oven.
All of these issues are addressed by Epo-Fix. It offers excellent sectioning qualities, good sample adhesion, low viscosity, easy mould curing (no orientation issues), and short cure durations.
Kit consists of:
- 2 x 500mL resin
- 130mL hardener
- 15 disposable paper cups and wooden spatulas
- 1 measuring syringe 20 ml and 1 syringe 5ml
Epo-Fix Technical Data:
A two-component epoxy resin with little shrinkage during curing and excellent mechanical qualities once cured. It's especially well-suited to embedding hard materials with complex shapes and vacuum impregnation. Epo-Fix can be utilised with a variety of samples, including paper, silicon, ceramics, metals, wafers, and chips. It has a low viscosity, a low vapour pressure, excellent wetting qualities, and very little shrinkage. It hardens in about 8 hours at room temperature without generating substantial heat (no harm from heat or pressure), and it hardens in about 2 hours at 60 degrees C. It's worth noting that putting Epo-Fix in a desiccator while it cures will eliminate any air bubbles.