- 泽任订制
- FST动物实验器械
- 瑞士ideal-tek镊子
- 瑞士Dumont镊子
- Techni-Tool
- 瑞士Rubis镊子
- arosurgica
- Genesee Scientific
- Gilder Grids
-
Entegris
- WEICON
- ACCURIS
- AIMS
- RMC钻石刀
- Sipel镊子
- 德国WIHA
-
Si-Mat
- Jokari
- Circuitmedic
-
Glissando病理切片扫描仪
- KNIPEX(凯尼派克)
- Swann-morton
- Cellpoint Scientific
- Swanstrom
- All-spec
- 新华器械
- Excelta
- MENDA
- MEISEI
- Erem
- Regine
-
OPTRASCAN病理扫描仪
- Benchmark
-
IDEAL
- 大龙仪器
- 五洋医疗
- Hozan(宝山)
- 3M
- Stoelting
- Roboz
-
Diatome钻石刀
- Fine Science Tools
- PLATO
-
抗原检测
- NanoSoft
-
Avantama
-
PSI打击器及配件
- Aptum
- xuron
- SPI
- ASI Instruments
-
上海一恒
-
上海雷磁
- Quantifoil
- 上海方需
- 苏州六六
-
Hamilton
- ISMART
-
显微镜
-
Bonllmann
- AVEN
- 塔望科技
-
瑞典Haglof激光测距仪
- STILLE
-
美国安维迪
- 德国贝朗蛇牌
- Medline
-
蛋白纯化系统
-
OHAUS奥豪斯
- 康博特森
- Ossila
- 赛宁(苏州)生物
- Bernstein
- 洁盟清洗机
- Ted Pella
- DSI
- Keller
-
Smart Tweezers
- 瑞士PB
-
Microscopes Internat...
- Lattice Gear
-
凯氏定氮仪
- lindstrom
- 美国EMS
-
1-material
-
仪器
- realisticflies
- Boive
- Zivic
Part of the Institute of Physics award-winning Ossila Solar Cell Prototyping platform , the Ossila Solar Cell I-V System is a low-cost solution for reliable characterisation of photovoltaic devices. The PC software (included with all variants of the system) measures the current-voltage curve of a solar cell and then automatically calculates key device properties. In addition, I-V measurements can be performed periodically over time to track the stability of these properties.
The system is available with either manual or automatic pixel switching (if you are using one of Ossila's substrate systems), or without a test board for use with your own substrate and testing system or if you already own one of our test boards. Please refer to the table under the specifications tab if you are not sure which model you should choose. This system is covered by our FREE 2-year warranty.
Solar Cell I-V Test System Specifications
Voltage Source | ±333 μV to ±10 V |
Current Measurement | ±10 nA to ±200 mA |
Substrate Size | 20 mm x 15 mm or 25 mm x 25 mm |
Substrate Compatibility - T2002A/T2003A | S101 (OLED substrates) |
Substrate Compatibility - T2002B/T2003B | S211 (PV substrates) |
Substrate Compatibility - T2002B/T2003C | S171 (Pixelated cathode substrates) |
Substrate Compatibility - T2002E/T2003E | S2006 (ITO Glass Substrates - PV and OLED 25mm Square) |
Overall Dimensions - Manual |
Source Measure Unit: Width: 125 mm; Height: 55 mm; Depth: 185 mm Test Board: Width: 105 mm; Height: 40 mm; Depth: 125 mm |
Overall Dimensions - Automated | Width: 155 mm; Height: 73 mm; Depth: 317 mm |
System Selection Guide
The table below will help you determine which system is right for you. The manual version of the system has switches on the test board itself, which the user operates to measure the different pixels on a solar cell device. The automated version of the system uses a multiplexing test board, which switches between these pixels automatically. Note, if you use one of our substrates listed in the table and another kind of substrate as well, we recommend manual pixel switching, as the test board can be detached and replaced with another one.
Key Features
Calculates Device Properties
The included PC software automatically calculates key properties of solar cells from the measured I-V curves. These properties include: the power conversion efficiency (PCE), fill factor (FF), short-circuit current density (Jsc), open-circuit voltage (Voc), maximum power (Pmax), shunt resistance (Rsh), and series resistance (Rs).
Rapid Characterisation
If you are using one of our substrate systems, the Solar Cell I-V System can be purchased with a multiplexing test board (just select the 'automated' variant of your choice in the drop-down list), which enables automatic pixel switching. As an added bonus, the temperature and light will also be recorded during the measurement!
Easy-to-Use
Just plug in the system, install the PC software, and you're ready to go! The intuitive interface and clean design makes the Solar Cell I-V System easy-to-use, simplifying the characterisation of solar cells.
Wide Measurement Range
The built-in source measure unit is capable of delivering voltages between -10 V and +10 V, with a maximum resolution of 333 μV, and measuring currents from as low as ±10 nA up to ±200 mA.
Measure Device Stability
By performing repeated current-voltage measurements over an extended period of time, the stability of key device properties can be tracked.
Multiple System Types Available
Choose from our range of system types (automated, manual, or source measure unit only) depending on your requirements. If you are unsure which model to select, refer to our comparison table on the specifications tab or contact us for advice.
System Type | No Test Board | Manual | Multiplexer |
±10 V Source Range | Yes | Yes | Yes |
±333 μV Source Resolution | Yes | Yes | Yes |
±200 mA Measurement Range | Yes | Yes | Yes |
±10 nA Measurement Resolution | Yes | Yes | Yes |
Software Included | Yes | Yes | Yes |
Automatic Solar Cell Characterisation | Yes | Yes | Yes |
Single Pixel Solar Lifetime Measurement | Yes | Yes | Yes |
For Use With S2006, S101, S211, or S171 Substrates | No | Yes | Yes |
Automatic Pixel Switching | No | No | Yes |
Multiple Pixels Solar Lifetime Measurement | No | No | Yes |
Please note that a solar simulator (not included) is needed to obtain standard efficiency measurements. Ossila does not currently supply solar simulators.