产品中心
- 泽任订制
- FST动物实验器械
- 瑞士ideal-tek镊子
- 瑞士Dumont镊子
- Weller
- Techni-Tool
- 瑞士Rubis镊子
- arosurgica
- Genesee Scientific
- Gilder Grids
-
Entegris
- WEICON
- ACCURIS
- AIMS
- RMC钻石刀
- Sipel镊子
- 德国WIHA
-
Si-Mat
- Jokari
- Circuitmedic
-
Glissando病理切片扫描仪
- KNIPEX(凯尼派克)
- Swann-morton
- Cellpoint Scientific
- Swanstrom
- All-spec
- 新华器械
- Excelta
- MENDA
- MEISEI
- Erem
- Regine
-
OPTRASCAN病理扫描仪
- Benchmark
-
IDEAL
- 大龙仪器
- 五洋医疗
- Hozan(宝山)
- 3M
- Stoelting
- Roboz
-
Diatome钻石刀
- Fine Science Tools
- PLATO
- NanoSoft
-
Avantama
-
PSI打击器及配件
- Aptum
- xuron
- SPI
-
抗原检测
- ASI Instruments
-
上海一恒
-
上海雷磁
- Quantifoil
- 上海方需
- 苏州六六
-
Hamilton
- ISMART
-
显微镜
-
Bonllmann
- AVEN
- 塔望科技
-
瑞典Haglof激光测距仪
- STILLE
-
美国安维迪
- 德国贝朗蛇牌
- Medline
-
蛋白纯化系统
-
OHAUS奥豪斯
- 康博特森
- Ossila
- 赛宁(苏州)生物
- Bernstein
- 洁盟清洗机
- Ted Pella
- DSI
- Keller
-
Smart Tweezers
- 瑞士PB
-
Microscopes Internat...
- Lattice Gear
-
凯氏定氮仪
- lindstrom
- 美国EMS
-
1-material
-
仪器
- realisticflies
- Boive
- Zivic
产品详情
简单介绍:
SPI经销商、原装进口、质量保证、任何产品问题请联系我司销售。
详情介绍:
eit-C™ CCC Conductive Carbon Cement is electrically conductive, and was formulated specifically for the mounting of samples for examination by SEM.
Because of its electrical conductivity, all samples are ready for insertion into the SEM immediately after drying of the product. If it is a non-conductive specimen, then there is the strong likelihood that some kind of metallization would be preformed on the sample, such as by sputter coating or if a FESEM is being used, possibly even by osmium coating.
The Leit-C CCC conductive adhesive contains only carbon, hydrogen, and oxygen, therefore after drying, there would be no peaks detected by EDS other than the three elements, even with windowless detectors. If the entire specimen holder is "painted" with CCC, the cement will mask the holder and in general, one does not detect x-rays from the holder itself and would could interfere with x-rays from the specimen itself.
Some Additional Information:
The product is considered air drying and the application of heat is not necessary. For use in a UHV system, so long as it will not change the sample itself, a bake-out can be done up to 100° C. Going to higher temperatures should cause degradation of the small amount of acrylic polymer binder present. Also, as one uses the product, and there is evaporation of the carrier, addition of the special thinner will enable the user to maintain constant viscosity and carbon solids.
Choice of Thinners:
We offer a choice of thinners, one being the "official" thinner formulated by the manufacturer of the Leit-C CCC adhesive product, and a second (and less expensive) one formulated by SPI Supplies.
Because of its electrical conductivity, all samples are ready for insertion into the SEM immediately after drying of the product. If it is a non-conductive specimen, then there is the strong likelihood that some kind of metallization would be preformed on the sample, such as by sputter coating or if a FESEM is being used, possibly even by osmium coating.
The Leit-C CCC conductive adhesive contains only carbon, hydrogen, and oxygen, therefore after drying, there would be no peaks detected by EDS other than the three elements, even with windowless detectors. If the entire specimen holder is "painted" with CCC, the cement will mask the holder and in general, one does not detect x-rays from the holder itself and would could interfere with x-rays from the specimen itself.
Some Additional Information:
The product is considered air drying and the application of heat is not necessary. For use in a UHV system, so long as it will not change the sample itself, a bake-out can be done up to 100° C. Going to higher temperatures should cause degradation of the small amount of acrylic polymer binder present. Also, as one uses the product, and there is evaporation of the carrier, addition of the special thinner will enable the user to maintain constant viscosity and carbon solids.
Choice of Thinners:
We offer a choice of thinners, one being the "official" thinner formulated by the manufacturer of the Leit-C CCC adhesive product, and a second (and less expensive) one formulated by SPI Supplies.